Rago Fabrication 2nd Gen Tundra Under-Hood Air Compressor Mount

The Rago Fabrication 2nd Gen Tundra Air Compressor Mount is an under-hood bracket that positions an ARB Single or ARB Twin air compressor inside the engine bay of 2014–2021 Toyota Tundra trucks, keeping the unit close to its power source and out of the cargo area. Built by a veteran-founded shop in Chandler, Arizona, the mount is designed to compartmentalize the engine bay and is available in one configuration sized for the second-generation Tundra platform.

Ready When the Trail Ends

Airing down for rocky terrain and airing back up for the highway is a routine part of overlanding. A reliably mounted, accessible compressor makes both steps straightforward. Positioning the ARB compressor under the hood keeps it near its power source, shortens wiring runs, and frees up bed and cab space for gear. A dedicated mount also means the compressor stays put on rough trails rather than shifting around in a storage bin.

Fast Installation on Most Years

The mount installs in approximately 15 minutes and requires no drilling, trimming, or modification on 2014–2019 model years. On 2020–2021 Tundras, minimal drilling is required to attach the mount to the side wall; Rago Fabrication provides instructions for this step. Either way, the bracket goes in without permanent alteration to the truck's structure on the years that don't require it, which matters for owners who want to keep the build reversible.

ARB Compressor Compatibility and Switch Pros Mounting

The mount accepts both the ARB Single Air Compressor and the ARB Twin Air Compressor. Because the Single and Twin use different bolt spacing, the Single Compressor secures at two bolt locations on the mount as supplied; owners who want additional bolt locations can drill them. The bracket can also mount a Switch Pros SP-9100 power distribution module, consolidating compressor and switch wiring in one area of the engine bay.

Features

• ARB Compressor Fitment: accepts both the ARB Single Air Compressor and the ARB Twin Air Compressor
• Switch Pros Compatible: bracket accommodates a Switch Pros SP-9100 power distribution module
• No-Drill on Most Years: 2014–2019 Tundras require no drilling, trimming, or modification
• Quick Install: approximately 15 minutes from start to finish
• Under-Hood Placement: mounts in the engine bay to keep the compressor near its power source

Specifications

Who This Is For and Isn't

This mount suits 2014–2021 Toyota Tundra owners who run an ARB Single or ARB Twin air compressor and want it mounted under the hood in the engine bay rather than stored loose in the bed or cab. It works equally well for daily-driven trucks that see occasional trails and dedicated overland builds.

This mount does not fit Tundra model years before 2014 or after 2021, and it is not designed for compressors other than the ARB Single and ARB Twin. The ARB compressor, Switch Pros module, and any Rago Fabrication air system accessories are not included and are sold separately. On 2020–2021 Tundras, installation is not fully drill-free.

Common Questions

Which air compressors fit this mount?

The Rago Fabrication 2nd Gen Tundra Air Compressor Mount is designed to fit the ARB Single Air Compressor and the ARB Twin Air Compressor. The compressor is not included with the mount and must be purchased separately.

Does installation require drilling into the truck?

On 2014–2019 Tundras, the mount installs without any drilling, trimming, or modification. On 2020–2021 Tundras, minimal drilling is required to attach the mount to the engine bay side wall; Rago Fabrication provides instructions for this step.

Where in the truck does the mount sit?

The Rago Fabrication compressor mount positions the ARB compressor under the hood, inside the engine bay. This placement keeps the compressor close to its power source and frees up bed and cab space for other gear.

Can the Single Compressor use all the bolt locations on the mount?

Because the ARB Single and Twin compressors use different bolt spacing, the Single Compressor secures at two bolt locations on the mount as supplied. Owners who want additional bolt locations can drill them; no additional locations are required for a functional install.

Does this mount work with a Switch Pros power distribution module?

The Rago Fabrication 2nd Gen Tundra Air Compressor Mount can also accommodate a Switch Pros SP-9100 power distribution module, allowing compressor and switch wiring to be consolidated in one area of the engine bay. The Switch Pros unit is sold separately.