Flatline Van Co Mercedes-Benz Sprinter Front Skid Plate

The Flatline Van Co Sprinter Front Skid Plate is a bolt-on aluminum underbody shield for 2019-and-newer Mercedes-Benz Sprinter 1500, 2500, 3500, and 3500XD vans, covering 144-inch, 170-inch, and 170-inch Extended wheelbases in Low and High Roof configurations. Constructed from 5mm aluminum with integrated side bends for structural rigidity and mounted on 3mm stainless steel brackets, the plate puts a solid barrier between the trail and the engine without requiring any cutting, drilling, or permanent modification to the van. Four variants cover 2019–2022 4WD, 2023+ AWD, and both generations with a 2-inch lift.

Engine Protection Where the Trail Gets Rough

Off-pavement driving exposes the underside of a Sprinter's engine to rocks, debris, and trail hazards that can cause serious and costly damage. The Sprinter Front Skid Plate sits directly between those hazards and the engine's critical components, providing full-coverage defense on every run. Because the plate is 5mm aluminum with integrated side bends rather than a flat sheet, it resists flexing under impact. A glancing rock strike stays a glancing rock strike instead of a bent panel that no longer seals the gap.

Bolt-On Install, No Permanent Changes

The Sprinter Front Skid Plate mounts to the van's over-run brackets using the included 3mm stainless steel mounting brackets. No drilling, no cutting, and no permanent modifications to the front end are required. All hardware is included. Sprinter 3500 vans that do not have over-run brackets from the factory can install the skid plate using the separately sold Sprinter Frame Rail Support Brackets. The stainless steel mounting hardware is built to withstand repeated removal and reinstallation in harsh conditions, so the plate stays serviceable over the life of the van.

Maintenance Access in Five Screws

Dropping the Sprinter Front Skid Plate for an oil change or routine underside inspection requires removing only five screws, giving complete access to the entire underside of the engine. No complicated disassembly, no special tools beyond what the screws require. The plate can also be paired with the Flatline Van Co Sprinter Bull Bar for a complete front-end protection setup. Both are bolt-on and compatible with each other.

Features

• 5mm aluminum construction: integrated side bends add structural rigidity without unnecessary weight
• 3mm stainless steel mounting brackets: included hardware built for repeated use and harsh conditions
• Bolt-on installation: no cutting, drilling, or permanent modification required
• Five-screw drop: full underside access for oil changes and routine maintenance
• Lifted-van variants: dedicated options for vans running the Van Compass Striker 2-inch Lift Kit or Stage 6.3 System
• Bull Bar compatible: works as a standalone piece or alongside the Flatline Van Co Sprinter Bull Bar

Specifications

Who This Is For and Isn't

The Sprinter Front Skid Plate is built for 2019-and-newer Mercedes-Benz Sprinter 1500, 2500, 3500, and 3500XD van owners who take their van off-pavement and want to protect the engine from rock strikes and trail debris without cutting or drilling the front end. Lifted-variant options are available specifically for vans running the Van Compass Striker 2-inch Lift Kit or Stage 6.3 System.

The skid plate does not fit pre-2019 Sprinter generations. Sprinter 3500 vans that lack factory over-run brackets require the separately sold Sprinter Frame Rail Support Brackets to install this plate. The lifted variants are designed for the Van Compass lift systems noted above and are not intended for vans with other lift kits or stock suspension.

Common Questions

Does this skid plate fit a Sprinter 3500?

The Sprinter Front Skid Plate fits 2019-and-newer Sprinter 3500 and 3500XD vans, but Sprinter 3500 models do not come with over-run brackets from the factory. Sprinter 3500 owners will need to install the separately sold Sprinter Frame Rail Support Brackets to mount the skid plate.

What is different about the lifted-van variants?

The lifted Sprinter Front Skid Plate variants are designed specifically for vans running the Van Compass Striker 2-inch Lift Kit or the Van Compass Stage 6.3 System. These variants account for the changed geometry of a lifted front end. They are not intended for stock suspension or other lift kits.

Can I do an oil change without fully removing the skid plate?

Removing the Sprinter Front Skid Plate requires taking out only five screws, which drops the plate and gives complete access to the entire underside of the engine. Oil changes and routine maintenance can be completed without any complicated disassembly.

Does this skid plate work with the Flatline Van Co Sprinter Bull Bar?

Yes. The Sprinter Front Skid Plate is fully compatible with the Flatline Van Co Sprinter Bull Bar and can be run as a standalone piece or as part of a complete front-end protection setup with the bull bar. Both are bolt-on installations.

Is all mounting hardware included?

All hardware needed to mount the Sprinter Front Skid Plate is included. The kit comes with the 3mm stainless steel mounting brackets and the fasteners required for a complete bolt-on installation. No drilling, cutting, or sourcing additional hardware is required for 1500, 2500, and equipped 3500 vans.

WARNING: This product can expose you to chemicals including lead and lead compounds, DEHP and bisphenol A (BPA) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.