Flatline Van Co Aluminum Side Steps for Mercedes-Benz Sprinter

The Flatline Van Co Sprinter Van Aluminum Side Steps are drop-style running boards built entirely from aluminum (tubing, plating, and mount brackets alike) for 2007 and newer Mercedes-Benz Sprinter 1500, 2500, 3500, and 3500XD vans in 144-inch and 170-inch wheelbases. The lowered step height closes the gap into lifted and 4x4 Sprinters, and a no-slip dimpled tread delivers confident footing in rain, snow, and mud. Two wheelbase-specific versions are available: 144-inch and 170-inch.

Lighter Without Sacrificing Strength

The Sprinter Van Aluminum Side Steps use all-aluminum construction throughout: round tubing, plating, and mount brackets, keeping the steps noticeably lighter than comparable steel steps. The 5mm aluminum build and black powder coat finish resist corrosion and daily wear, so the steps hold up through years of use without adding unnecessary mass to the van. For builds where weight savings compound across every component, starting with aluminum steps rather than steel ones is a straightforward gain.

A Step Within Reach on Lifted Vans

Stock and lifted Sprinters sit high enough that climbing in and out repeatedly adds up, whether at a trailhead, a campsite, or a job site. The lowered drop-step design on the Sprinter Van Aluminum Side Steps shortens that reach to the cab and side door, putting a solid foothold where it is actually useful rather than tucked tight to the body for clearance. Buyers running a 4x4 or lifted Sprinter will notice the difference immediately.

No-Slip Tread That Matches the Ladder System

The step tread on the Sprinter Van Aluminum Side Steps uses an oval-dimple pattern that mirrors the tread on Flatline Van Co Sprinter ladders, creating a consistent grip surface and a cohesive look across the side of the van. That dimpled surface bites in when the step is wet, muddy, or icy, conditions where a smooth tread would be a liability. The steps are also designed to work alongside the Flatline Van Co Apex Side Ladder, Side Ladder, and Surf Pole for a fully integrated side-access setup.

Features

• All-aluminum construction: round tubing, plating, and mount brackets built from aluminum for reduced weight without sacrificing strength
• Lowered drop-step design: shortened reach to the cab and side door, especially useful on lifted and 4x4 Sprinters
• No-slip oval-dimple tread: matches Flatline Van Co Sprinter ladder tread pattern for grip and visual consistency
• Black powder coat finish: 5mm aluminum with a durable powder coat for corrosion resistance
• All hardware included: bolt-on installation with all needed fasteners in the box
• Ladder and Surf Pole compatible: designed to work with Flatline Van Co Apex Side Ladder, Side Ladder, and Surf Pole

Specifications

Who This Is For and Isn't

The Sprinter Van Aluminum Side Steps suit 2007 and newer Mercedes-Benz Sprinter 1500, 2500, 3500, and 3500XD owners in 144-inch or 170-inch wheelbases, low or high roof, passenger, cargo, or dually configuration, who want a lighter-weight, lower-reaching step for daily entry and exit, especially on lifted or 4x4 builds. Buyers integrating a Flatline Van Co ladder or Surf Pole will find the steps designed to work alongside that hardware.

These steps do not fit Sprinter vans with underbelly-mounted water tanks. They are not a high-clearance step: the drop-style design prioritizes ease of reach over maximum ground clearance, so buyers whose primary concern is protecting the step on technical terrain should consider a higher-mounted option. These steps do not fit Ford Transit, Ram ProMaster, or other van platforms.

WARNING: This product can expose you to chemicals including lead and lead compounds, DEHP and bisphenol A (BPA), which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Common Questions

Do these side steps fit a lifted or 4x4 Sprinter?

Yes. The Sprinter Van Aluminum Side Steps use a lowered drop-step design specifically intended to shorten the reach into lifted and 4x4 Sprinters, where the cab and side door sit higher off the ground than on a stock-height van. The steps fit 2007 and newer Sprinter 1500, 2500, 3500, and 3500XD in 144-inch and 170-inch wheelbases regardless of roof height.

Is drilling required to install these steps?

Yes, drilling is required to install the Sprinter Van Aluminum Side Steps. All mounting hardware is included in the box. The installation is a bolt-on process once the drilling is complete, and two people on hand for the job is recommended. Wheelbase-specific installation guides are available for both the 144-inch and 170-inch variants.

Will these steps work with Flatline Van Co ladders and the Surf Pole?

Yes. The Sprinter Van Aluminum Side Steps are designed to be compatible with the Flatline Van Co Apex Side Ladder, Side Ladder, and Surf Pole, allowing a coordinated side-access setup. The oval-dimple tread pattern on the steps also matches the tread used on Flatline Van Co Sprinter ladders for a consistent look and grip surface across the system.

What wheelbase and roof-height combinations do these steps fit?

The Sprinter Van Aluminum Side Steps are available in two variants: one for the 144-inch wheelbase and one for the 170-inch wheelbase. Both variants fit low-roof and high-roof Sprinters in passenger, cargo, and dually configurations. They do not fit Sprinter vans equipped with underbelly-mounted water tanks.

How do these aluminum steps compare to steel Sprinter side steps?

The Sprinter Van Aluminum Side Steps are built entirely from aluminum, including the tubing, plating, and mount brackets, making them lighter than steel side steps. The trade-off is step height: the drop-style design sits lower for easier access but offers less ground clearance than a high-clearance steel step mounted tight to the body. Buyers prioritizing maximum clearance on technical terrain should weigh that difference before choosing.