DV8 Offroad Spec Series Rear Bumper for Ram 2500/3500

The DV8 Offroad Spec Series Rear Bumper is a full-width steel replacement bumper for 2019–2026 Ram 2500 and 3500 trucks, all trims. Built from 3.5mm and 5mm steel plate with a bolt-on fit that requires no cutting, it adds rear-end protection for off-road travel, towing, and daily work-truck use while retaining the factory hitch receiver, OEM license plate lights, and factory sensor systems.

Full-Width Coverage Where It Counts

The Spec Series bumper spans the full width of the Ram HD's rear, covering the corners and lower valance areas that a factory bumper leaves exposed on the trail or at the worksite. That added coverage matters most when backing into brush, navigating tight two-track, or parking in tight lots where corner strikes are common. The 3.5mm and 5mm steel plate construction means the bumper absorbs contact that would crumple a factory plastic-and-foam assembly.

Trail Lighting Without the Wiring Mess

Integrated mounts accommodate two 3-inch rear-facing pod lights, positioned to illuminate directly behind the truck when backing down a trail, setting up camp in the dark, or working a job site after sunset. Welded-in zip tie tabs run alongside the mounting provisions so wiring stays routed cleanly against the bumper rather than zip-tied to whatever is nearby. Pod lights are sold separately.

Bolt-On Fit, Factory Features Intact

The Spec Series bumper installs without cutting or welding, with an estimated 3.5-hour installation time that will vary with experience. The factory hitch receiver, OEM license plate lights, and backup sensor provisions all carry over, so towing capability and safety systems remain fully operational after the swap. Trucks equipped with factory backup sensors should add DV8 Part # MPRSNSR-01 sensor bezels, sold separately, for a clean sensor fit in the new bumper.

Features

• Full-width steel construction: 3.5mm and 5mm steel plate for maximum rear coverage and impact resistance
• Pod light mounts: integrated provisions for two 3-inch rear-facing pod lights (lights sold separately)
• Welded zip tie tabs: built-in wire management points for a clean lighting installation
• Bolt-on installation: no cutting or welding required; estimated 3.5-hour install
• Factory system compatibility: retains OEM hitch receiver, license plate lights, and backup sensor provisions
• Micro-texture black powder coat: durable finish with satin black aluminum accent plates

Specifications

Who This Is For and Isn't

The DV8 Offroad Spec Series Rear Bumper fits 2019–2026 Ram 2500 and 3500 trucks (all trims) and suits owners who want added rear-end protection for off-road use, towing, or hard work-truck duty without giving up factory hitch, sensor, or lighting functionality.

This bumper does not fit Ram 1500 trucks or any Ram HD outside the 2019–2026 model years. Pod lights are not included. Trucks with factory backup sensors require DV8 Part # MPRSNSR-01 sensor bezels, sold separately, for a proper sensor fit.

Common Questions

Will this bumper work with my factory backup sensors?

The DV8 Offroad Spec Series Rear Bumper retains the factory sensor provisions, so backup sensors remain functional after installation. Ram 2500/3500 trucks equipped with factory backup sensors should also purchase DV8 Part # MPRSNSR-01 sensor bezels, sold separately, for a clean and proper sensor fit in the new bumper.

Are the pod lights included with the bumper?

The Spec Series Rear Bumper includes integrated mounting provisions for two 3-inch rear-facing pod lights, but the pod lights themselves are sold separately. The bumper also includes welded-in zip tie tabs to keep wiring routed cleanly once lights are added.

Does installation require cutting or welding?

The DV8 Offroad Spec Series Rear Bumper is a bolt-on replacement that requires no cutting or welding. Installation is estimated at approximately 3.5 hours, though actual time will vary depending on installer experience.

Does the factory hitch receiver carry over?

Yes. The Spec Series Rear Bumper is fully compatible with the factory hitch receiver on 2019–2026 Ram 2500/3500 trucks, so towing capability is retained after the bumper swap without any additional modification.

What is the bumper made of?

The DV8 Offroad Spec Series Rear Bumper is constructed from 3.5mm and 5mm steel plate and finished in a micro-texture black powder coat. Satin black aluminum accent plates are also included as part of the bumper assembly.

WARNING: This product can expose you to chemicals including lead, lead compounds, DEHP, and bisphenol A (BPA), which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.