DV8 Offroad Spec Series Rear Bumper for Ford Bronco

The DV8 Offroad Spec Series Rear Bumper is a fully bolt-on steel replacement bumper for the 2021–2026 Ford Bronco, covering all trim levels including the Bronco Raptor, constructed from 3.5mm and 5mm steel plate and finished in a micro-texture black powder coat with satin black aluminum accent panels. The bumper adds two 3-inch pod light mounts and two 1-inch D-ring recovery mounts while retaining the factory hitch, parking sensors, trailer plug, and license plate lights, with no cutting or drilling required.

Built-In Recovery Points Without Losing Factory Capability

Two 1-inch thick D-ring mounts, each accepting a 7/8-inch pin, are welded directly into the Spec Series Rear Bumper structure, providing dedicated rear recovery anchor points for a strap or shackle. Having structurally integrated mounts at the rear means recovery hardware can be attached quickly at a known anchor location rather than improvised around a frame rail or hitch ball. The factory hitch is fully retained, so towing capability carries over without modification.

Parking sensors, the trailer plug, and license plate lights remain fully operational after installation. Keeping these systems intact avoids the diagnostic codes and inspection complications that can result from aftermarket bumpers that block or eliminate OEM sensor positions.

Auxiliary Lighting Ready, Wiring Managed

Two dedicated 3-inch pod light mounts are built into the bumper ends, giving auxiliary rear lighting a clean, structurally sound home without additional brackets or fabrication. Welded-in zip tie tabs along the bumper interior provide anchor points for routing and securing wiring from aftermarket lights, keeping cables away from heat and moving components for a finished install appearance.

Bolt-On Installation Using Factory Mounting Points

The Spec Series Rear Bumper attaches to the Bronco's existing mounting points and includes all hardware needed for installation. No cutting, drilling, or frame modification is required. Estimated install time is 3 hours, though time will vary with experience. The satin black aluminum accent panels and aluminum-backed logo are shaped to complement the Bronco's factory body lines.

The bumper is compatible with the OEM swing-away tire carrier and clears a spare up to 37 inches in diameter. When running a 37-inch spare, full visibility of the third brake light requires the DV8 Offroad Third Brake Light Extension Bracket, sold separately.

Features

• Steel construction: 3.5mm and 5mm steel plate throughout
• Bolt-on fit: uses factory mounting points; no cutting or drilling required; all mounting hardware included
• Recovery mounts: two 1-inch thick D-ring mounts, each accepting a 7/8-inch pin
• Lighting provisions: mounts for two 3-inch pod lights; welded-in zip tie tabs for wire management
• OEM retention: factory hitch, parking sensors, trailer plug, and license plate lights all remain operational
• Finish: micro-texture black powder coat; satin black aluminum accent panels; aluminum-backed logo

Specifications

Who This Is For and Isn't

The Spec Series Rear Bumper suits 2021–2026 Ford Bronco owners (including Bronco Raptor drivers) who want integrated rear recovery points and auxiliary lighting mounts without giving up factory towing, sensor, or spare tire carrier functionality. It fits overlanding and off-road builds where a factory-complementary appearance matters alongside added trail capability.

This bumper does not fit the Ford Bronco Sport or any pre-2021 Bronco generation. Running a 37-inch spare on the OEM carrier without the DV8 Offroad Third Brake Light Extension Bracket (sold separately) will obstruct the third brake light. Pod lights and D-ring shackles are not included with the bumper.

Common Questions

Does this bumper fit the Bronco Raptor?

The DV8 Offroad Spec Series Rear Bumper fits all 2021–2026 Ford Bronco trim levels, including the Bronco Raptor. No trim-specific modifications or adapters are required for any variant.

Is cutting or drilling required to install this bumper?

No cutting or drilling is required. The Spec Series Rear Bumper is a fully bolt-on design that attaches to the Bronco's existing mounting points. All mounting hardware is included, and estimated install time is approximately 3 hours, though that will vary with experience.

Will the factory hitch and trailer plug still work after installation?

Yes. The Spec Series Rear Bumper retains full use of the factory hitch and trailer plug, so towing capability is not affected. Parking sensors and license plate lights are also retained and remain fully operational.

What is the largest spare tire the OEM carrier will clear with this bumper installed?

The Spec Series Rear Bumper is compatible with the factory swing-away tire carrier and accommodates spare tires up to 37 inches in diameter. When running a 37-inch spare, the DV8 Offroad Third Brake Light Extension Bracket (sold separately) is required to maintain full third brake light visibility.

Are D-ring shackles and pod lights included?

The Spec Series Rear Bumper includes two 1-inch thick D-ring mounts (each accepting a 7/8-inch pin) and two 3-inch pod light mount locations built into the bumper, along with all hardware needed to bolt the bumper to the vehicle. D-ring shackles and pod lights are not included and must be sourced separately.