DV8 Offroad Crash Bar Caps with Accessory Mount for Ford Bronco

The DV8 Offroad Crash Bar Caps cover the open ends of the factory crash bar left exposed after installing an aftermarket front bumper on a 2021-2026 Ford Bronco. Constructed from 3mm steel with a micro-texture black powder coat finish, each cap includes an integrated accessory mount sized for light pods, rock lights, or an action camera. These fit all Bronco trims from 2021 through 2026, excluding the Raptor, and accommodate up to 35-inch tires with the Sasquatch package or an equivalent aftermarket lift.

A Finished Look After Your Bumper Swap

Most aftermarket front bumpers leave the crash bar's tube ends open, a visible gap that looks unfinished and can collect trail debris. The DV8 Offroad Crash Bar Caps cover those ends cleanly, giving the front end a complete, intentional appearance without cutting or fabricating anything. The micro-texture black powder coat matches the matte finish common on off-road bumpers, so the caps blend rather than stand out.

A Mounting Point You Would Otherwise Have to Fabricate

Each crash bar cap includes an integrated accessory mount that accepts light pods up to 3 inches, rock lights, RGB accent lights, or an action camera such as a GoPro. That position, low and forward on the crash bar, puts a camera at an angle suited for rock crawling footage and puts auxiliary lighting where it can illuminate obstacles directly in front of the bumper. Note that light pods, rock lights, and wiring harnesses are sold separately; minor wiring is required to use the lighting mount.

Bolt-On Installation in About 30 Minutes

The crash bar caps use a direct-fit, bolt-on design that utilizes factory hardware already on the crash bar, so no drilling or cutting is required for the caps themselves. DV8 Offroad estimates installation at approximately 30 minutes, though time will vary depending on experience. Minor wiring is needed if you plan to use the accessory mount for lighting.

Features

• Fitment: 2021-2026 Ford Bronco, all trims excluding Raptor; accommodates up to 35-inch tires with Sasquatch package or equivalent aftermarket lift
• Integrated accessory mount: accepts light pods up to 3 inches, rock lights, RGB accent lights, or an action camera
• 3mm steel construction: micro-texture black powder coat finish
• Bolt-on installation: direct fit using factory hardware; estimated 30-minute install
• Minor wiring required: when using the accessory mount for lighting (lights and harness sold separately)

Specifications

Who This Is For and Isn't

These crash bar caps suit 2021-2026 Ford Bronco owners (all trims except Raptor) who have installed or are planning to install an aftermarket front bumper and want to cover the exposed crash bar ends cleanly while gaining a forward-facing mount for auxiliary lighting or an action camera.

These caps do not fit the Ford Bronco Raptor. They are not compatible with stock Bronco bumpers that leave the crash bar enclosed. Light pods, rock lights, RGB lights, wiring harnesses, and action cameras are not included and must be purchased separately. Minor wiring is required to power any lighting connected to the accessory mount.

Common Questions

Which Ford Bronco years and trims do these crash bar caps fit?

The DV8 Offroad Crash Bar Caps (LBBR-07) fit 2021 through 2026 Ford Broncos across all trims, with one exception: they do not fit the Ford Bronco Raptor. They are designed for Broncos running up to 35-inch tires with the Sasquatch package or an equivalent aftermarket lift.

Do lights or a wiring harness come included with these caps?

No lights, rock lights, or wiring harness are included with the DV8 Offroad Crash Bar Caps. The caps provide the accessory mount; light pods, RGB lights, and wiring harnesses must be purchased separately. Minor wiring is required to connect any lighting to the accessory mount.

What accessories can I mount on the crash bar caps?

The integrated accessory mount on each DV8 Offroad Crash Bar Cap accepts light pods up to 3 inches in diameter, rock lights, RGB accent lights, and action cameras such as a GoPro. The forward-low position on the crash bar makes it well suited for capturing rock crawling footage or illuminating obstacles directly in front of the bumper.

Do these caps require drilling or cutting to install?

The DV8 Offroad Crash Bar Caps use a direct-fit, bolt-on design that utilizes factory hardware already on the crash bar, so no drilling or cutting is required for the caps themselves. Installation is estimated at approximately 30 minutes, though time will vary by experience level. Minor wiring is needed if you plan to use the accessory mount for lighting.

WARNING: This product can expose you to chemicals including lead and lead compounds, DEHP and bisphenol A (BPA) which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.