{"product_id":"c4-fabrication-overland-series-4th-gen-4runner-front-bumper","title":"C4 Fabrication Overland Series 4th Gen 4Runner Front Bumper","description":"\u003cp class=\"product-lead\"\u003eThe C4 Fabrication Overland Series Front Bumper is a steel replacement front bumper for the 4th Generation Toyota 4Runner (2003–2009), built from 3\/16-inch laser-cut P\u0026amp;O steel with 1\/4-inch thick frame and winch plates. At 120 lb in the no-bull-bar configuration, it replaces the factory bumper with a winch-ready, recovery-point-equipped platform designed to improve approach angles and accommodate larger tires. Two year-range variants (2003–2005 and 2006–2009) and three bull bar configurations are available; select the correct year range at checkout, as included hardware differs between them.\u003c\/p\u003e\n\n\u003ch2\u003eClearance Where It Counts\u003c\/h2\u003e\n\u003cp\u003eThe Overland Series bumper is shaped to open up approach angles compared to the factory unit, which matters on steep ledge entries and rocky descents where the stock bumper's lower profile catches first. The additional clearance also gives room for larger-diameter tires without the rubbing or trimming that a factory bumper can force. For 2003–2005 model years, a bolt-on top fill plate is included to close the gap left by the bumper swap, a detail that keeps the front end looking finished rather than patched.\u003c\/p\u003e\n\n\u003ch2\u003eRecovery-Ready Construction\u003c\/h2\u003e\n\u003cp\u003eEvery Overland Series bumper ships with 3\/4-inch thick D-ring tabs fully welded front and back, providing solid recovery attachment points without add-on hardware. The frame and winch plates are 1\/4-inch thick, and frame support brackets and a washer tank skid are included in the box. The winch pocket fits most 8,000–12,000 lb winches; winches with a relocatable electrical control box are recommended, as integrated control box designs may require trimming of the grille support brackets. Synthetic rope with a hawse-style fairlead is recommended. Some roller fairleads are too large for the recessed fairlead mounting plate and may not fit without modification.\u003c\/p\u003e\n\n\u003ch2\u003eLighting and Bull Bar Options\u003c\/h2\u003e\n\u003cp\u003eThe bumper accepts a 30-inch single-row light bar and is specifically designed around the Baja Designs S8. Turn signal holes are pre-drilled, and signals or caps are included depending on the year range selected. Three bull bar configurations are offered: no bull bar, mid-height bull bar, and full-height bull bar with plate gussets. Bull bar tubing is .120-wall, 1-3\/4-inch diameter HREW tubing. Weight increases with bull bar size: 120 lb with no bull bar, 128 lb with the mid-height, and 130 lb with the full-height and plate gussets.\u003c\/p\u003e\n\n\u003ch2\u003eFinish and Installation\u003c\/h2\u003e\n\u003cp\u003eThe Overland Series bumper is available in raw (bare steel) or powder coat finish. Raw variants must be painted or powder coated before installation to prevent rust; test fitting before coating is recommended to confirm alignment and fitment. The bumper is compatible with up to 2-inch body lifts. Professional installation is recommended for a product of this weight and complexity.\u003c\/p\u003e\n\n\u003ch2\u003eFeatures\u003c\/h2\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSteel construction:\u003c\/strong\u003e 3\/16-inch laser-cut P\u0026amp;O steel body with 1\/4-inch frame and winch plates\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRecovery points:\u003c\/strong\u003e 3\/4-inch thick D-ring tabs, fully welded front and back, included on every bumper\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWinch-ready:\u003c\/strong\u003e fits most 8,000–12,000 lb winches; hawse fairlead and synthetic rope recommended\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLight bar mount:\u003c\/strong\u003e accepts 30-inch single-row light bars, designed for Baja Designs S8\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eIncluded hardware:\u003c\/strong\u003e frame support brackets, washer tank skid, pre-drilled turn signal holes with signals or caps by year range, bolt-on top fill plate for 2003–2005\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eBull bar options:\u003c\/strong\u003e no bull bar, mid-height, or full-height with plate gussets in .120-wall 1-3\/4-inch HREW tubing\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eSpecifications\u003c\/h2\u003e\n\u003ctable\u003e\n  \u003cthead\u003e\n    \u003ctr\u003e\n      \u003cth\u003eSpecification\u003c\/th\u003e\n      \u003cth\u003eNo Bull Bar\u003c\/th\u003e\n      \u003cth\u003eMid-Height Bull Bar\u003c\/th\u003e\n      \u003cth\u003eFull-Height Bull Bar w\/ Plate Gussets\u003c\/th\u003e\n    \u003c\/tr\u003e\n  \u003c\/thead\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWeight\u003c\/td\u003e\n      \u003ctd\u003e120 lb\u003c\/td\u003e\n      \u003ctd\u003e128 lb\u003c\/td\u003e\n      \u003ctd\u003e130 lb\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eBody steel\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003e3\/16-inch laser-cut P\u0026amp;O steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eFrame and winch plates\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003e1\/4-inch steel\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eBull bar tubing\u003c\/td\u003e\n      \u003ctd\u003eN\/A\u003c\/td\u003e\n      \u003ctd colspan=\"2\"\u003e.120-wall, 1-3\/4-inch diameter HREW\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eD-ring tabs\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003e3\/4-inch thick, fully welded front and back\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eWinch capacity\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003eMost 8,000–12,000 lb winches\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eLight bar\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003e30-inch single-row (designed for Baja Designs S8)\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eFinish options\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003eRaw (bare steel) or powder coat\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eVehicle fitment\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003eToyota 4Runner, 4th Generation, 2003–2009\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eBody lift compatibility\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003eUp to 2-inch body lift\u003c\/td\u003e\n    \u003c\/tr\u003e\n    \u003ctr\u003e\n      \u003ctd\u003eCountry of origin\u003c\/td\u003e\n      \u003ctd colspan=\"3\"\u003eUSA\u003c\/td\u003e\n    \u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch2\u003eWho This Is For and Isn't\u003c\/h2\u003e\n\u003cp class=\"product-fit-yes\"\u003eThe Overland Series Front Bumper suits 4th Generation Toyota 4Runner owners (2003–2009) who want a winch-capable, recovery-ready front end with improved approach angles for off-road and overlanding use. It works with up to 2-inch body lifts and accommodates larger tires than the factory bumper allows.\u003c\/p\u003e\n\u003cp class=\"product-fit-no\"\u003eThis bumper does not fit any 4Runner generation outside of 2003–2009 (4th Gen). Winches are not included and are sold separately. Raw-finish buyers must arrange painting or powder coating before installation; the bumper will rust if installed bare. Integrated control box winches may require trimming of the grille support brackets and are not guaranteed to fit without modification.\u003c\/p\u003e\n\n\u003ch2\u003eCommon Questions\u003c\/h2\u003e\n\u003ch3 class=\"product-faq-q\"\u003eWhich 4Runner years does this bumper fit?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eThe C4 Fabrication Overland Series Front Bumper fits the 4th Generation Toyota 4Runner, model years 2003 through 2009 only. Two year-range variants are offered (2003–2005 and 2006–2009) because included hardware differs between them: 2003–2005 buyers receive turn signal caps or signals and a bolt-on top fill plate, while 2006–2009 buyers receive turn signal caps or signals only. Select the correct range at checkout.\u003c\/p\u003e\n\n\u003ch3 class=\"product-faq-q\"\u003eWhat winches fit this bumper?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eThe Overland Series Front Bumper accommodates most 8,000–12,000 lb winches. Winches with a relocatable electrical control box are recommended; winches with an integrated control box (such as some ComeUp, Smittybilt X20, Warn Zeon, and Warn VR series models) may require trimming of the grille support brackets. Winches are not included and must be purchased separately.\u003c\/p\u003e\n\n\u003ch3 class=\"product-faq-q\"\u003eWhat fairlead style works with this bumper?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eThe Overland Series bumper uses a recessed fairlead mounting plate, and a hawse-style fairlead with synthetic rope is recommended for best fitment and function. Some roller fairleads have a footprint too large for the recessed plate and may not fit without modification.\u003c\/p\u003e\n\n\u003ch3 class=\"product-faq-q\"\u003eDo I need to paint or coat the raw-finish bumper before installing it?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eYes. Raw (bare steel) variants of the Overland Series Front Bumper must be painted or powder coated before installation to prevent rust. Test fitting the bumper before coating is recommended to confirm alignment and fitment on the vehicle first.\u003c\/p\u003e\n\n\u003ch3 class=\"product-faq-q\"\u003eWhat is included with the bumper?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eEvery Overland Series Front Bumper includes frame support brackets, a washer tank skid, pre-drilled turn signal holes with signals or caps (depending on year range), and fully welded 3\/4-inch D-ring tabs. The 2003–2005 variant also includes a bolt-on top fill plate. Winches, light bars, and fairleads are not included and are sold separately.\u003c\/p\u003e\n\n\u003ch3 class=\"product-faq-q\"\u003eWill this bumper work with a body lift?\u003c\/h3\u003e\n\u003cp class=\"product-faq-a\"\u003eThe C4 Fabrication Overland Series Front Bumper is compatible with body lifts up to 2 inches. Body lifts exceeding 2 inches are not supported.\u003c\/p\u003e","brand":"C4 Fabrication","offers":[{"title":"Raw \/ 2003-2005 \/ No Bull Bar","offer_id":50629355274310,"sku":"1100-3103-30-NB","price":1949.99,"currency_code":"USD","in_stock":true},{"title":"Raw \/ 2003-2005 \/ Mid-Height Bull Bar","offer_id":50629355307078,"sku":"1100-3103-30-MH","price":1999.99,"currency_code":"USD","in_stock":true},{"title":"Raw \/ 2003-2005 \/ Full-Height Bull Bar w\/ Plate Gussets","offer_id":50629355339846,"sku":"1100-3103-30-FH","price":2049.99,"currency_code":"USD","in_stock":true},{"title":"Raw \/ 2006-2009 \/ No Bull Bar","offer_id":50629355372614,"sku":"1100-3106-30-NB","price":1798.99,"currency_code":"USD","in_stock":true},{"title":"Raw \/ 2006-2009 \/ Mid-Height Bull Bar","offer_id":50629355405382,"sku":"1100-3106-30-MH","price":1949.99,"currency_code":"USD","in_stock":true},{"title":"Raw \/ 2006-2009 \/ Full-Height Bull Bar w\/ Plate Gussets","offer_id":50629355438150,"sku":"1100-3106-30-FH","price":1957.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2003-2005 \/ No Bull Bar","offer_id":50629355470918,"sku":"1100-3103-30-NB-01NA","price":2099.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2003-2005 \/ Mid-Height Bull Bar","offer_id":50629355503686,"sku":"1100-3103-30-MH-01NA","price":2149.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2003-2005 \/ Full-Height Bull Bar w\/ Plate Gussets","offer_id":50629355536454,"sku":"1100-3103-30-FH-01NA","price":2199.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2006-2009 \/ No Bull Bar","offer_id":50629355569222,"sku":"1100-3106-30-NB-01NA","price":2099.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2006-2009 \/ Mid-Height Bull Bar","offer_id":50629355601990,"sku":"1100-3106-30-MH-01NA","price":2099.99,"currency_code":"USD","in_stock":true},{"title":"Powder Coat \/ 2006-2009 \/ Full-Height Bull Bar w\/ Plate Gussets","offer_id":50629355634758,"sku":"1100-3106-30-FH-01NA","price":2199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0691\/2203\/1686\/files\/4thGen4RunnerOverlandBumperCover.jpg?v=1791946053","url":"https:\/\/terrainvault.com\/products\/c4-fabrication-overland-series-4th-gen-4runner-front-bumper","provider":"TerrainVault","version":"1.0","type":"link"}